STM32F407IGT6 MCU Core Board, Cortex-M4, 168MHzUSB HS/FS, Ethernet, 1GBit Onboard Nand Flash, 1024kB Flash, 192+4kB SRAM, XCore407I
Make: WaveShare Electronics Co.
SKU: 2406
Availability: IN STOCK

₹3,120.51 inc. GST
Ex GST: ₹2,644.50
Qty:
 


Additional Info
  • Prices shown are Including GST.
  • B2B GST Credit Available.
  • Economy shipping at flat ₹49.
  • Free shipping on value > ₹2499.
  • Whatsapp Support @+917231066325


  • XCore407I is an STM32 MCU core board that features the STM32F407IGT6 on board.

    • Clock circuit, USB power management
    • Onboard devices: USB HS PHY、Ethernet PHY、1G Bit NandFlash
    • Connectors:USB HS (mini / type A), USB FS (mini), Ethernet (RJ45)
    • All the idle I/O ports are accessible on the pin headers
    • 2.0mm pin header pitch, smaller size, easier to integrate into user system

    Developer Resources at Wiki: www.waveshare.com/wiki/XCore407I


     

    STM32F407IGT6 development board on board resource

    1. 1. STM32F407IGT6:the high performance STM32 MCU which features:
      • Core: Cortex-M4 32-bit RISC
      • Feature: a full set of single-cycle DSP instructions
      • Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
      • Operating Voltage: 1.8V-3.6V
      • Package: LQFP176
      • Memories: 1024kB Flash, 192+4kB SRAM
      • MCU communication Interfaces:
        • 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C
        • 1 x FSMC, 1 x SDIO, 2 x CAN
        • 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
        • 1 x 10/100 Ethernet MAC
        • 1 x 8 to 14-bit parallel camera interface
      • AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
      • Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
    2. 2. MIC2075-2, onboard USB FS power management device
    3. 3. AMS1117-3.3, 3.3V voltage regulator
    4. 4. K9F1G08U0E, 1G Bit NandFlash
    5. 5. DP83848, Ethernet PHY
    6. 6. MIC2075-1, onboard USB HS power management device
    7. 7. USB3300, USB HS PHY
    8. 8. Power supply switch, powered from 5Vin or USB connection
    9. 9. Boot mode switch, for configuring BOOT0 pin
    10. 10. Power indicator
    11. 11. USB FS LED
    12. 12. USB HS LED
    13. 13. Reset button
    14. 14. 8M crystal, MCU clock, enables the MCU run at higher speed by frequency multiplication
    15. 15. 24M crystal, USB3300 clock
    16. 16. 50M crystal, DP83848 clock
    17. 17. 32.768K crystal, for internal RTC with calibration
    18. 18. Ethernet connector
    19. 19. USB FS mini connector
    20. 20. USB HS mini connector
    21. 21. USB HS type A connector
    22. 22. MCU pins expander, VCC, GND and all the idle I/O ports are accessible on expansion connectors for further expansion
    23. 23. USB OTG/HOST jumper
    24. 24. VREF/VBAT jumper
    25. 25. Ethernet I/O selection solder joint
    26. 26. USB HS I/O selection solder joint
    27. 27. PDR selection solder joint: 1.8-3.6V, -40~105℃ OR 1.7-3.6V, 0~70℃

    STM32 MCU core board dimensions

     

    Write a review

    Your Name:


    Your Review: Note: HTML is not translated!

    Rating: Bad           Good

    Enter the code in the box below: