2-Channel Isolated CAN FD Expansion HAT for Raspberry Pi
Make: WaveShare Electronics Co.
SKU: 17075
Availability: OUT OF STOCK

₹3,479.82 inc. GST
Ex GST: ₹2,949.00
Qty:
 

QuantityPrice
10 + ₹1,803.04
More Quantity?RFQ

Additional Info
  • Prices shown are Including GST.
  • B2B GST Credit Available.
  • Economy shipping at flat ₹59.
  • Free shipping on value > ₹2499.
  • Whatsapp Support @+917231066325
  • Estimated Delivery time?
  • Manufacturing Services

  •  

    Introduction

    This is a 2-Channel CAN bus expansion HAT designed for Raspberry Pi, supports CAN FD (CAN with Flexible Data-Rate), the speed is higher than the traditional 1Mbps of CAN2.0, features multi onboard protection circuits, high anti-interference capability, and stable operation. It suits for fields such as automotive devices or industrial automation.

    Features

    • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards
    • Supports both traditional CAN2.0 and CAN FD protocols, up to 8Mbps data rate
    • Breakout SPI control pins, for connecting with host control boards like STM32/Arduino
    • Onboard electrical isolation, up to 5KV isolated voltage, high anti-interference capability, stable operation
    • Onboard lighting proof, ESD, short circuit protection, more safe communication
    • Onboard voltage translator, select 3.3V/5V operating voltage by jumper
    • Onboard 120Ω terminal resistor, configured by jumper
    • Comes with development resources and manual (examples for Raspberry Pi/Arduino)

    Specifications

    • CAN controller: MCP2517FD
    • CAN transceiver: MCP2562FD
    • Communication interface: SPI (two channels independent SPI by default, swith to one channel SPI by soldering)
    • Power supply: external power input terminal, or Raspberry Pi
    • Power input terminal voltage: DC 8~26V
    • Operating voltage: 5V
    • Logic level: 3.3V/5V
    • Dimensions: 65.0 x 56.5 mm

    Interfaces

    CAN interface
    PIN Raspberry Pi (BCM2835) Raspberry Pi (WPI) Description
    5V 5V 5V 5V Power input
    GND GND GND Ground
    MISO_0 9 (MISO) 13 (MISO) SPI_0 Data output
    MOSI_0 10 (MOSI) 12(MOSI) SPI_0 Data input
    SCK_0 11 (SCK) 14 (SCK) SPI_0 Clock input
    CS_0 8 (CE0) 10 (CE0) CAN_0 Chip select
    INT_0 25 6 CAN_0 Interrupt Pin
    MISO_1 9/19 (MISO) 13/24 (MISO) SPI_1 Data output
    MOSI_1 10/20 (MOSI) 12/28 (MOSI) SPI_1 Data input
    SCK_1 11/21(SCLK) 14/29 (SCLK) SPI_1 Clock input
    CS_1 7(CE1)/26 11(CE1)/25 CAN_1 Chip select
    INT_1 16 27 CAN_1 Interrupt Pin
     

     


    Development Resource - Product Wiki Page for Resources


    2-CH CAN FD HAT on board resource

    1. 1. CP2517FD CAN controller
    2. 2. MCP2562FD CAN transceiver
    3. 3. SI8642ED digital isolator
    4. 4. MP1584EN power chip
    5. 5. RT9193-33 power chip
    6. 6. B0505LS-1W power supply isolation module
    7. 7. Raspberry Pi GPIO connector: for connecting Raspberry Pi
    8. 8. CAN terminal
    9. 9. External power input terminal: DC 8~26V input
    10. 10. MCU control pin: for connecting with host control boards like Arduino
    11. 11. 120Ω terminal resistor configuration
    12. 12. 3.3V/5V logic level selection
    13. 13. CAN operating mode selection:
      1. A: CAN_0 and CAN_1 use two channels independent SPI (default)
      2. B: CAN_0 and CAN_1 share one common SPI
    14. 14. Power indicator
    15. 15. 2A fast auto-recovery fuse
    16. 16. Power supply anti-reverse diode
    17. 17. Power supply anti-countercurrent diode
    18. 18. Follow current diode
    19. 19. SM24CANB TVS diode array

    Write a review

    Your Name:


    Your Review: Note: HTML is not translated!

    Rating: Bad           Good

    Enter the code in the box below: