Compute Module IO Board Plus, for Raspberry Pi CM3 / CM3L / CM3+ / CM3+L
Make: WaveShare Electronics Co.
SKU: 2398
Availability: IN STOCK

₹4,953.64 inc. GST
Ex GST: ₹4,198.00
Qty:
 


Additional Info
  • Prices shown are Including GST.
  • B2B GST Credit Available.
  • Economy shipping at flat ₹49.
  • Free shipping on value > ₹2499.
  • Whatsapp Support @+917231066325

  • The Compute Module IO Board Plus is a development board which you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. It is compatible with the Compute Module IO Board V3 from the Raspberry Pi Foundation, along with various common use components.


    Developer's Resources : https://www.waveshare.com/wiki/Compute_Module_IO_Board_Plus


    Features : 

    • → Compatible with the Compute Module IO Board V3 from the Raspberry Pi Foundation
    • → Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs
    • → Arduino connectivity, also supports Arduino shields
    • → 1-WIRE interface, for connecting single-bus devices like DS18B20
    • → 4x keys, 4x LEDs, 1x Buzzer, for I/O testing
    • → Onboard USB HUB, allows connecting more USB devices
    • → IR receiver, IR remote control is available
    • → Onboard USB TO UART, for serial debugging
    • → Sensor interface
    • → 10-bit ADC, 38KSPS, 11-ch (6-ch for Arduino interface, 5-ch for sensors)
    • → 16-bit DAC, 2-ch
    • → Onboard RTC, one of the most common and useful functions

    • 1. Compute Module interface: for connecting Compute Module (CM3 / CM3L / CM3+ / CM3+L)
    • 2. Compute Module GPIO header: breakout all the Compute Module pins
    • 3. Raspberry Pi GPIO header: for connecting Raspberry Pi HATs
    • 4. CSI interface: camera ports, for connecting Raspberry Pi Camera
    • 5. DSI interface: display ports, for connecting Raspberry Pi LCD
    • 6. HDMI port
    • 7. USB ports: for connecting USB devices
    • 8. USB SLAVE interface: allows you to burn system image in to Compute Module 3/3+
    • 9. USB TO UART interface: for serial debugging
    • 10. Arduino header: for connecting Arduino shields
    • 11. AD/DA input/output screw terminals
    • 12. 1-WIRE interface: for connecting single-bus devices like DS18B20\
    • 13. Sensor interface
    • 14. Power port: 5V 2.5A
    • 15. FE1.1S: USB HUB chip
    • 16. 12MHz crystal
    • 17. CP2102: USB TO UART converter
    • 18. Micro SD card slot: insert a Micro SD card with pre-burnt system, to start up Compute Module 3/3+ Lite variant
    • 19. TLC1543: AD converter
    • 20. DAC8552: 16-bit DAC, 2-ch
    • 21. DS3231: high-precision RTC chip, I2C interface
    • 22. RTC battery holder: supports CR1220 batteries
    • 23. Voltage regulator: 3.3V / 2.5V / 1.8V 
    • 24. LFN0038K: IR receiver
    • 25. Buzzer
    • 26. Power indicator
    • 27. ACT indicator: indicating the Micro SD card status
    • 28. User LEDs
    • 29. User Keys
    • 30. BOOT selection
      • EN: enable the PC to access SD card/eMMC through USB SLAVE
      • DIS: the Compute Module will boot from SD card/eMMC
    • 31. VGx power selection: config the I/O level
    • 32. USB HUB enable jumper: HUB enable and USB SLAVE power selection
    • 33. ADC/DAC configuration: config the power supply and reference voltage of ADC/DAC
    • 34. Peripheral configuration: config the control pins of UART, user keys, user LEDs, 1-WIRE interface, IR receiver, and buzzer
    • 35. Arduino AD selection
      • connect 1 and 2: Arduino A0-A5 as digital control pin
      • connect 2 and 3: Arduino A0-A5 as AD input

    Write a review

    Your Name:


    Your Review: Note: HTML is not translated!

    Rating: Bad           Good

    Enter the code in the box below: