Li-Poly Battery HAT for Raspberry Pi - 3000mAh Li-Poly Battery - Quick Charge
Make: WaveShare Electronics Co.
SKU: 2202
Availability: Sold Out

₹1,996.56 inc. GST
Ex GST: ₹1,692.00
Qty:
 

QuantityPrice
25 + ₹1,811.30
More Quantity?RFQ

Additional Info
  • Prices shown are Including GST.
  • B2B GST Credit Available.
  • Economy shipping at flat ₹49.
  • Free shipping on value > ₹2499.
  • Whatsapp Support @+917231066325

  • Instruction

    The Li-polymer Battery HAT integrates SW6106 power bank management chip, allows providing 5V regulated power supply to your Raspberry Pi or other 5V devices, from a high capacity Li-polymer battery. It will charge the battery as well, supports bi-directional quick charge.

    Features

    • Onboard SW6106 chip, supports bi-directional quick charge, supports multi quick charge protocols like PD/QC/FCP/PE/SFCP
    • Lithium battery protection circuitry, provides reverse protection, overcharge protection, and short circuit protection
    • Onboard indicators: quick charge, power capacity
    • PH 2.0 battery connector, for connecting the 3.7V 3000mA high capacity Li-polymer battery (MSDS certified)

    Specifications

    • Output voltage: 5V
    • Charge voltage: 5V
    • Applicable battery: 3.7V Li-polymer battery (4.2V when full charged)
    • Dimension: 65.0mm × 56.5mm
    • Mounting hole size: 3.0mm

    Interfaces and Indicators

    • Interfaces
    Interface Description
    Micro USB Charge
    USB Type-A Power output
    USB Type_C Suports chrage, quick charge and power output
    • There are five battery indicators.
    Capacity LED1 LED2 LED3 LED4 LED5
    80%~100% ON ON ON ON ON
    60%~80% ON ON ON ON Blink
    40%~60% ON ON ON Blink OFF
    20%~40% ON ON Blink OFF OFF
    5%~20% ON Blink OFF OFF OFF
    1%~5% Blink OFF OFF OFF PFF
    0% OFF OFF OFF OFF OFF
    • Quick start indicator
    When you connect power adapter to Type_C interface for quick charging, the Quick Charge indocator will turn on. If it keeps on, maybe that your adapter doesn't support quick charge.
    • Standby button
    Single-press it to output 5V, and double-press it to set it to sleep mode.

    How to use

    Discharge

    Connect it to Raspberry Pi
    • Step1: Insert the Li-polymer battery to 2.0mm battery socket.
    • Step2: Single-press Standby button, set it to discharge mode
    • Step3: Attach it on Raspberry Pi for powering.
    For other devices.
    • Step1: Insert the Li-polymer battery to 2.0mm battery socket.
    • Step2: Single-press Standby button, set it to discharge mode
    • Step3: Connect it to other devices by USB cable or wires.

    Charge

    Charge
    • Step1: Insert the Li-polymer battery to 2.0mm battery socket.
    • Step2: Connect power adapter to micro USB or Type-C interface by USB cable
    Quick charge
    • Step1: Insert the Li-polymer battery to 2.0mm battery socket.
    • Step2: Connect power adapter (support quick charge) to type_C interface by USB cable
    • Step3: Check if the Quick charge indicator turns on.

    Notices

    • Module enter sleep mode when the working current is less than 40mA and stop to discharge.
    • The Quick charge mode only works when you connect a power adapter that supports quick charge.
    • To power Raspberry Pi, you can attach it on the GPIO or connect Type_A interface to Pi by USB cable.
    • This module cannot work as UPS. It will turn off Raspberry Pi when low-voltage.
    • The battery is about 4.2v when fully charged. Note that you should discharge the battery to 3.0, otherwise it is damaged.
    • Please disconnect any devices when you replace battery.
    • DO NOT change the battery provided with other battery without protective panel.
    • Please check the poles of the battery interface carefully when you connect batteries.

    Resource

    Write a review

    Your Name:


    Your Review: Note: HTML is not translated!

    Rating: Bad           Good

    Enter the code in the box below: