Raspberry Pi Compute Module 4 IO Board With PoE Feature (Type B), for all Variants of CM4
Make: WaveShare Electronics Co.
SKU: 2585
Availability: IN STOCK

₹4,332.96 inc. GST
Ex GST: ₹3,672.00
Qty:
 


Additional Info
  • Prices shown are Including GST.
  • B2B GST Credit Available.
  • Economy shipping at flat ₹49.
  • Estimated Delivery time?
  • Free shipping on value > ₹2499.
  • Whatsapp Support @+917231066325

  • Raspberry Pi Compute Module 4 IO Board With PoE Feature (Type B), for all Variants of CM4

    This is an IO board for evaluating the Raspberry Pi CM4 or being integrated into end products. the board features the PoE function (Type B), which can be used for all variants of CM4.


    Technical Resources [External Link]

     

    Precautions for use

    1: It is forbidden to unplug and plug any equipment other than USB and HDMI when power is on
    2: Confirm the fan voltage before connecting. It supports 5V and 12V. The default connection is 5V. Please modify the jumper of FAN_VCC
    3: Type C interface can be used for power supply or USB SLAVE interface for burning image.
    4: In order to ensure the normal power supply of CM4, please do not connect other devices when using the Type C interface to burn the image.
    5: When CM4 is in normal use, it needs to provide 5V 2A power supply for CM4. Otherwise, problems such as automatic shutdown, frequency reduction, etc. may occur.
    6: USB2.0 is closed by default, if you need to open it, you need to add dtoverlay=dwc2,dr_mode=host


     

     

     

    No. Component Description
    1 CM4 socket Suitable for all variants of Compute Module 4
    2 40PIN GPIO header ~
    3 BOOT selection ON: CM4 would be booted from USB-C interface
    OFF: CM4 would be booted from eMMC or Micro SD card
    4 Misc functional pins ~
    5 USB Type-C power supply / programming 5V/2.5A power supply,
    also allows burning system image into Compute Module 4 eMMC variants
    6 Status indicators ACT: Raspberry Pi operating status indicator
    PWR: Raspberry Pi power indicator
    7 DISP 2x MIPI DSI display port
    8 CAM 2x MIPI CSI camera connectors.
    9 USB2.0 ports 4x USB2.0 ports, for connecting sorts of USB devices
    10 HDMI ports 2x HDMI ports, supports dual 4K 30fps output
    11 RTC battery holder supports CR1220 button cell
    12 FAN header for connecting cooling fan, allows speed adjustment and measurement
    13 PCIe Gen 2 × 1 socket forconnecting PCIe Gen 2 × 1 modules
    14 Gigabit Ethernet connector Gigabit Ethernet RJ45 with PoE support, 10/100/1000M compatible
    15 DC 5V output ~
    16 RS485 with 600W lightning-proof, anti-surge, and 15KV ESD protection,
    reversed optional 120R balancing resistor jumper
    17 RS232 with TVS diode, anti-surge, and ESD protection
    18 Buzzer ~
    19 FAN_VDD/PoE selection cooling fan driving voltage: 12V or 5V
    PoE: enable (EN) or disable (DIS)
    20 FE1.1S USB expansion chip
    21 PCF52063ATL RTC chip
    22 RTC/FAN I2C bus switch,
    SDA0/SCL0: I2C-10 is shared with CSI/DSI
    GPIO3/2: I2C-1 is shared with 40PIN header
    23 IO logic level selection set the CM4 IO logic level as 3.3V or 1.8V
    24 RTC interruption configuration PI-RUN: CM4 will reboot on RTC interruption
    GN-EN: CM4 powerdown on RTC interruption
    D4: D4 pin is triggered on RTC interruption
    25 Micro SD card slot insert a Micro SD card with pre-burnt system, to start up Compute Module 4 Lite
     

     

     

    Write a review

    Your Name:


    Your Review: Note: HTML is not translated!

    Rating: Bad           Good

    Enter the code in the box below: