We are off for a few days. All the order placed during 11th October to 21st October will be dispatched on 22-23 October 2017. Support will be available through eMail or Whatsapp at 7231066325.

Arduino UNO Plus - Arduino UNO R3 compatible
Brand: WaveShare Electronics Co.
Product Code: R-1731
Reward Points: 10
Availability: In Stock

Rs 1,099.00
Qty:
 


Price in reward points: 999
Delivery Information
  • Free Shipping on total order amount Rs. 1999 and more.
  • Shipping starts at Rs. 50
  • Expected delivery within 4-8 Days, Depending on Location!
  • We dispatch all orders on next working day.[Monday-Friday]
  • View Our Packaging Standards
  • Arduino UNO Plus - Arduino UNO R3 compatible

    UNO PLUS is a development board compatible with the Arduino UNO R3, an improved & enhanced alternative solution for Arduino UNO R3.


    Comparison chart of UNO PLUS Vs UNO R3:

      UNO PLUS UNO R3 Remarks
    Operating voltage 5V/3.3V 5V Dual voltage level to support more shields
    Reset Lateral Vertical Lateral button is easier to use when connecting with shield
    Bootloader switch Yes None The board can be configured to run program immediately when power-up by the switch
    USB connector Micro USB USB Type B Micro connector is more commonly used, and shields won't be blocked anymore while connecting
    DC jack Low profile Normal height Shields won't be blocked anymore while connecting
    Power output header Yes None

    Providing 5V/3.3V power output OR common-grounding with other boards

    3.3V power output 800mA Max 150mA Max UNO PLUS features higher driving capability
    Oscillator Crystal oscillator Ceramic resonator Crystal oscillator is suit for applications where accurate clock reference is required
    ADC channel 8 6 CFG used as ADC6 by configuration, and ADC7 from the Reserved PIN
    Connecting with prototype breadboard Supported Not supported Solder pads is provided for DIY interfaces to connecting with prototype breadboard
    USB driver Compatible with all main systems Doesn't compatible with WIN7/WIN8 Express Edition Driver will never failed to install thanks to the onboard FT232
    Firmware fixing Supported Not supported Firmware can be fixed by using the onboard FT232, no extra programmer is needed

    What's on the UNO PLUS

    UNO-PLUS on board resource

    1. 1. ATMEGA328P-AU
    2. 2. AMS1117-3.3 : 3.3V voltage regulator
    3. 3. NCP1117ST50T3G : 5V voltage regulator
    4. 4. FT232RL : USB to UART convertor
    5. 5. Arduino interface
      • compatible with standard Arduino interface with two additional analog inputs A6 (config the CFG), A7
      • solder pads provided, supports prototype breadboard
    6. 6. ICSP interface
    7. 7. MICRO USB connector : for uploading program OR serial port debugging
    8. 8. Power output header : 3.3V OR 5V, voltage level configured by the onboard power configuration switch, used as power output OR common-grounding with other boards
    9. 9. FT232 pins : for burning Bootloader into the microcontroller
    10. 10. DC input : 7V ~ 12V
    11. 11. Reset button
    12. 12. Power indicator
    13. 13. Serial port Rx/Tx indicator
    14. 14. User LED
    15. 15. Power configuration switch : for configuring the operating voltage
    16. 16. Bootloader selection switch
      • turn ON : the board will reset when power-up OR other USB devices were detected connecting to the PC
      • turn OFF : the onboard program runs immediately when power-up, and the board will not reset when other USB devices were detected connecting to the PC

     

    Write a review

    Your Name:


    Your Review: Note: HTML is not translated!

    Rating: Bad           Good

    Enter the code in the box below: